Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
Listed here below yow will discover lots of extremely good information and facts about A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old tub with a new one is likewise a reasonably tough job. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make sure you have actually certified on your own for the task as well as fit attempting it. Instead of hiring a contractor to take over a halfway-completed job, it is much better to think about employing one prior to you start. Chances are you might need an expert plumber to make tube links.
This post will assist you install a brand-new bath tub in your restroom if you have currently bought a new bathtub and also do not require to transform the arrangement of your previous water pipes.
Your devices and material list must comprise the following:
Getting ready for the Setup
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent stress on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome as a result of the limited access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. When the supply pipes have been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. When the taps have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed position. The wood boards are helpful in evenly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub till the spirit level checks out degree.
To install taps, fit the bottom of the furthest flexible faucet port to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water and check all joints and new pipework for leaks and tighten them if required. Fill the tub as well as likewise check the overflow outlet and the normal outlet for leaks.
Ultimately, repair the bath paneling as described in the maker's user's manual. Tiling and securing around the bath tub ought to wait up until the tub has actually been utilized at least once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin making certain that the washers remain in location between the faucet and the sink. Secure the tap in place with the manufacturer supplied backnut. Once the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, causing the water to pass through the wall between the bath and the tiling, bring about difficulties with dampness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill the tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can break rather very early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly offered on the market. It is recommended to fit the floor tiles using waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that piece of writing about How to Install a Bathtub Yourself when doing a search on the search engines. Sharing is caring. Helping people is fun. I am grateful for your time. Please pay a visit to our blog back soon.
Expertise on line! Report this page